ZDMAK FOREIGN CAR TOOLS FOR VOLKSWAGENVOLKSWAGEN and MoreBar and Pin for 5 Valve 99.95- (Found July 5, 2008 ) Camshaft Timing Tool Set (2) TOOL REF 3391 CamBar Holder V6 5 valves per cylinder used for the crucial task of securing both engine banks camshafts at T.D.C when replacing the timing belt to properly align camshaft during timing belt change head assembly work. Applicable VW Audi V6 5 Valve 1998 2003 CamBar Holder Not Applicable 3.0 2002 4 cam. TOOL REF 3242 Crankshaft T.D.C. Lock Pin Holds crankshaft at top dead center For installing or removing toothed belt...http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VW3391X3242&CTMP=1&LowC... Bench Head Stand 34.99- (Found July 5, 2008 ) NUMBER ZDM HDSTAND Bench Head Stand Set Aluminum & Steel Heads This Head Stand set has been designed for use on most cylinder heads. In operation, it holds the head off the bench for valve work, head cleaning and assembly. Its holding rods have a log 5 inch taper which allows them to go further into the stud hole for more contact in the hole and a firmer grip on the head. These holding rods are also heat treated to remain smooth for use on aluminum heads.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=SCH-88150&CTMP=1&LowCt=... Brake Bleeder Wrench 9mm 9.99- (Found July 5, 2008 ) Offset Brake Bleeding Wrench 9mm x 7mm.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AW-80619G&CTMP=1&LowCt=... Brake Piston Tool 14.99- (Found July 5, 2008 ) Disc Brake Piston Cube Tool has 5 different drive pin configurations designed to rotate the parking brake activated piston back into the caliper cylinder when replacing worn pads on vehicles equipped with 4 wheel disc brakes. Tool will service many domestic and import cars. This tool will work in place of special tool 3272. Some Audi VW calipers (mid 80s) use a hex tool check yours to be certain a pain in the neck if you have never done them before. Grind or file off two diagonally.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AW-80621C&CTMP=1&LowCt=... Brake Release Tool 28.50- (Found July 5, 2008 ) NUMBER 3289 Brake Release Tool Volkswagen VR6 Jetta Tool is used to disconnect brake pedal from booster. This is an Original VW Factory Tool Made in Germany for Volkswagen by Kukko.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VW3289&CTMP=1&LowCt=0 BALL JOINT PULLER 0.00- (Found July 5, 2008 ) BALL JOINT TOOL USED TO REMOVE BALL JOINTS ON CONTROL ARM AND STABILIZER BAR Click here for more options 3287http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VW3287A&CTMP=1&LowCt=0 Cam Bar for 2 Valve 98.00- (Found July 5, 2008 ) Camshaft Securing Bar Timing Tool TOOL REF 3243 CamBar Holder 2 valves per cylinder Used for the crucial task of securing both engine banks camshafts at T.D.C when replacing the timing belt to properly align camshaft during belt change head assembly work. Applicable Audi 90 A6 A4 94 97 AFC Engine Please note: 3243 Securing Bar for 2 valves per cylinder. http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VW3243&CTMP=1&LowCt=0 Cam Bar for 5 Valve 98.50- (Found July 5, 2008 ) Camshaft Timing Tool Securing Bar TOOL REF 3391 Cam Securing Bar Holder V6 5 valves per cylinder used for the crucial task of securing both engine banks camshafts at T.D.C when replacing the timing belt to properly align camshaft during timing belt change head assembly work. Applicable VW Audi V6 5 Valve 1998 2003 CamBar Holder Not Applicable 3.0 (2002 4 cam) Please note: 3391 for 5 valves per cylinder. http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VW3391&CTMP=1&LowCt=0 Cam Set T40030 199.50- (Found July 5, 2008 ) Cam Tool Kit (2) T40030 USED FOR LOCKING AND COUNTER HOLDING CAMSHAFT TOOLS ARE SOMETIMES USED IN CONJUNCTION WITH TOOL NUMBERS T40028, T40011 AND T40026 (NOT INCLUDED) This is a two piece set T40030 ONLY. Please note: You can buy any of the components (T40028, T40011 and T40026) or the complete 4 piece set to see the options simply type T40030 in the search field. This sale is for a two piece set T40030 ONLY. Comes in the plastic carrying case.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=T40030&CTMP=1&LowCt=0 Camber Adjustment Tool 18.75- (Found July 5, 2008 ) VA6004 Camber Adjustment Tool For proper alignment of camber VW Dasher Fox Same as old VW number 4471http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VA6004&CTMP=1&LowCt=0 |