ZDMAK FOREIGN CAR TOOLS FOR ZDMAK SPECIALSZDMAK SPECIALS and MoreHeadbolt Tool for BMW 19.99- (Found July 8, 2008 ) Headbolt Tool for BMW Socket is designed to fit in the cylinder head on M42 and M50 engines to remove and install cylinder headbolts. Spring loaded detent ball holds bolt in place. Socket size is E12 for external TORX bolts. Heavy Duty tool 12 inch drive.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-5011-E12&CTMP=1&LowC... Heater Hose Coupler Repair Kit 62.50- (Found July 8, 2008 ) Heater Hose Coupler Repair Kit For use on GM quick disconnect heater hose fittings found on many GM models using the 3.1L, 5.0L, 5.7L and 6.5L engines Includes storage case with tray. This repair kit removes even the most corroded heater hose couplers on GM vehicles. Kit contains a Heater Hose Coupler Remover that can be driven into couplers and then turned out with a 58'' socket or wrench. When the coupler is extremely corroded the special tapered, reverse drill can be used to...http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MKL-62450&CTMP=1&LowCt=... Heavy Duty Extractor 99.50- (Found July 8, 2008 ) Heavy Duty Extractor BMW3030 Needed for the proper disassembly of ball joint from lower wishbone. Applicable: Most BMW models. BASE OF OPENING=25.5mmhttp://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=BMW3030&CTMP=1&LowCt=0 Heavy Duty Hex 13.99- (Found July 8, 2008 ) Hex Socket 8mm Heavy Duty Tool. Overall Length is 4 inches38 drive end size.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-STRH8&CTMP=1&LowCt=0 Drill Pump ZDMAK SPECIAL 9.95- (Found July 8, 2008 ) Easily attatches to most electric drills (Minimum 1,200 R.P.M.) Pumps up to 8 feet Standard garden hose threads. Testimonial: I have used this Drill Pump for years and am totally impressed with the quality. Recent improvements have made this tool even better. Other drill pumps just do not compare. After one or two uses the impellers separate from the shaft but not with this one! Keep this Drill Pump on the shelf. Sincerely, L. Kagawa Mira Loma, CAhttp://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AW-1143C&CTMP=1&LowCt=0 Electrical Connector Separator 9.99- (Found July 8, 2008 ) Electrical Connector Separator Quickly disconnects electrical connectors without damage Works on Weather Pack and other automotive electrical connectors Engage tool tip behind the connector clip. Push or pull to disconnect. The tool is double ended to fit different access angles.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=GTL-13120C&CTMP=1&LowCt... Exhaust Back Pressure Tester 53.50- (Found July 8, 2008 ) Exhaust Back Pressure Tester Test for clogged or obstruucted catalytic converters and mufflers. Fast and easy to use. Threads into Oxygen Sensor Port. Kit includes 12MM and 18MM adapters to fit most domestic and imported vehicles. Gage measures 2 12" diameter and has dual scale: 15 PSI and 1.00KgCm2. Hose is 41" long. No need to tap into exhaust system then reseal holes afterwards. Packed in a vinyl pouch for store display and tool box storage. Complete with instructions.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=WT-3360E&CTMP=1&LowCt=0 Feeler Guage Holder and Blade 5.00- (Found July 8, 2008 ) Single Feeler Guage Holder and Blade for Porsche 911 Tool Comes as shown with one blade .004" picture is for reference only)http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=SCH-88600A&CTMP=1&LowCt... Feeler Guage Holder and Blade 5.00- (Found July 8, 2008 ) New improved P213 Single Feeler Guage Holder and Blade for the correct adjustment of Valve clearance Porsche 911 Tool Comes as shown with one blade .004" Quality Sir Tools product, Made in Europe.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=P213N&CTMP=1&LowCt=0 Ferrari Head Bolt Tool 39.95- (Found July 8, 2008 ) Please note this is a 15mm offset wrench for Ferrari Headbolts. The tool is 12 inch drive. Extra long and with a deep offset for recessed bolts. Offset head. Check your manuals to be sure of the size (15mm) needed.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-FE15MM&CTMP=1&LowCt=... |