ZDMAK FOREIGN CAR TOOLS FOR VOLVO TOOLSVOLVO TOOLS and MorePiston Ring Groove Cleaner 16.99- (Found June 19, 2008 ) Piston Ring Groove Cleaner Easily clean carbon and deposits from ring grooves. Comes with two wheels with five cutters for a total of 10 groove cleaning sizes.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AW-80576C&CTMP=1&LowCt=... Press Kit 34.95- (Found June 19, 2008 ) For proper installation of waterpump 99 , 900Use with tool SA 010http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VO-SA015&CTMP=1&LowCt=0 Press Set 2 Only from Cam Kit 00- (Found June 19, 2008 ) Press tools (pair) appl: 700, 800, 850, 900, 960, C70 Conv, C70 Coupe, S40, S60, S70, S80, S90, V40, V70 2000, V70 2000 , V70 XC, V70 XC 2001 , V70 XC 2001 XC70, V90, XC90, Engine:B4164SEngine:B4164S2, Engine:B4184S, Engine:B4184S10, Engine:B4184S2, Engine:B4184S3, Engine:B4184S9, Engine:B4194T, Engine:B4194T2, Engine:B4204S, Engine:B4204S2, Engine:B4204T, Engine:B4204T2, Engine:B4204T2 CVVT, Engine:B4204T3, Engine:B4204T3http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VO-V55XPRESS2&CTMP=1&Lo... Pressure Adaptor 28.50- (Found June 19, 2008 ) Pressure Adaptor 1018 Used for pressuring the master cylinder or clutch slave cylinder reservoirs. Used in conjunction with a pressure bleeder. Comes with a 14 18 NPT threaded opening. Applicable:Most Volvo "Except" S40 and V40.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=1018&CTMP=1&LowCt=0 Puller 79.00- (Found June 19, 2008 ) Puller Same as Volkswagen Tool 3032 Injection Pump Tool Used for the proper extraction of injection pump drive gear. Applicable:VW Audi diesels Excluding TDIhttp://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VA6005&CTMP=1&LowCt=0 Puller plus Pin , Plate and Holder 140.00- (Found June 19, 2008 ) 4 Tools for VW Audi Volvo repair. These 4 tools are required for timing belt replacement and fuel injection pump timing, as well as fuel injection pump removal on pre TDI Volkswagen, Audi, and Volvo Diesels, both 4 cylinder and 5 cylinder versions using Bosch mechancial diesel injection from 1977 to 1995. Tool 2065a engages the offset slot at the rear of the camshaft. This locks the camshaft to the surface of the cylinder head, holding the camshaft at TDC. Thus you are able to.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VW2064BONUS4&CTMP=1&Low... Puller, Pin , Plate , Holder , Pin Wrench 156.00- (Found June 19, 2008 ) Set of five tools: vw 3032, VA6015 PLUS 2065A PLUS 2064 PLUS 12717 Details:3032 Injection Pump Tool Puller used for the proper extraction of injection pump drive gear. Applicable: Volvo and VW Audi diesels Excluding TDI PLUS: VA6015 Used for accurate adjustment of Bosch diesel injection pump. PLUS: 2065A Diesel Camshaft Locking Plate Tool PLUS: 2064 Lock Pin for Diesel. Plus the Pin Wrench (made in Germany) for easy adjustment of Camshaft spur belts (toothed belt) on idler Pulleys.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=VW2064DX5&CTMP=1&LowCt=... Mini Bit Holder and Set 12.95- (Found June 19, 2008 ) Nice Mini Ratchet Bit Set. These are mainly Tamperproof bits in this set. THE SEVEN BITS ON THE LEFT SIDE OF THE SET ARE "TORX TAMPERPROOF) Plus this set has a number 1 and 2 Phillips bitsPlus a flat head bit. The Torx sizes are: T10, T15, T20, T25, T30, T40 The Torx have a hole in the tip (tamperproof).http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-U-11MC&CTMP=1&LowCt=... Special 17mm Crowfoot Socket 92.98- (Found June 19, 2008 ) 17mm Crowfoot Socket 38 Drive for injection lines on BMW Diesel overall length is 115mm.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=HAZET4550&CTMP=1&LowCt=... Split Socket 9.99- (Found June 19, 2008 ) Deep Split Socket size 78 Removes and Installs Oxygen Sensors on Many Domestic and some Imports. Special Socket with slotted cutout for clearance of wire harness. Provides proper depth to fit over the sensor. Use with 12 square drive or wrench end. Provides adequate depth to fit over sensor. Heat treated alloy steel.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-1606&CTMP=1&LowCt=0 |