ZDMAK FOREIGN CAR TOOLS FOR ZDMAK SPECIALSZDMAK SPECIALS and MoreSuper Long 3mm Hex 11.50- (Found July 8, 2008 ) SUPER LONG 3mm Hex AllenOverall Length 15 inches.T Handle Hex Tool Blades of Special CRM 72 Tool Steel Through Hardened Anti corrosion Nickel Finish Ergonomic Comfort Grip T Handle Shaped for Maximum Power & Comfort Handle Molded over L Key for permanent bond Guaranteed Quality Made In Germany!http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=W-33435&CTMP=1&LowCt=0 Subaru Drain Plug Tool 14.99- (Found July 8, 2008 ) Heavy Duty Subaru Drain Plug ToolSturdy compact Heavy Duty Design. Satin Chrome with black impact tips. Super New S2 Alloy Steel Fully Heat Treated (Drivers heat treated to 56 to 62 RC)http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-SUB70&CTMP=1&LowCt=0 STUD ALIGNMENT SET 13.99- (Found July 8, 2008 ) WHEEL STUD ALIGNMENT GUIDE TOOL SET Tools assist when mounting wheels, especially late models with long lug bolts. This is a set of 2. You will get one of each size with this purchase. You will get one tool thread size M14 x 1.5 and you also get one tool size M12 x 1.5.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-1124X1853&CTMP=1&Low... Stubby Angle Driver 8.50- (Found July 8, 2008 ) Stubby Driver Ratcheting Screwdriver allows access to confined areas. Bits are stored in handle end. Contains Drive, 1 and 2 Phillips 316 and 14 slotted bits.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AW-934A&CTMP=1&LowCt=0 Thin Wrench 24mm 15.00- (Found July 8, 2008 ) Thin Wrench Chrome Plated. Specially designed, this tool is thinner than regular wrench, used on thin nuts and for getting into spaces. The size of this wrench is 24mm. The overall length is just under 7 inches. The thickness of this wrench is 14 inch All mechanics need thin wrenches occasionally to work on transmissions, gas tanks or changing a wheel on a creeper seat. This intermittent use does not justify the very high price charged by the competition; this is one of very few...http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-85950-24&CTMP=1&LowC... Thumbwheel RatchetSet 3 23.00- (Found July 8, 2008 ) Set of all three Spinners14, 38 and 12 Drive Thumbwheel RatchetsThumbwheel design makes tightening or loosening fasteners fast and easy. Fully polished face with Knurled grip for better control.3 Super tools for serious mechanics!http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AW-32123MK3&CTMP=1&LowC... T6 Terminal Tool 34.50- (Found July 8, 2008 ) Introducing the T6 Terminal Tool The "Swiss Army Knife" of wire terminal extractors. This internationally patented design offers the technician a handy "all in one" extractor kit that folds up and slides together into its own unique and compact storage housing. This kit is equipped with (6) factory correct extractor press bits. These press bits release DC wiring terminals from its harness that connect to ECUs, sensors, etc., found on most every late model vehicle.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=ST9024&CTMP=1&LowCt=0 Valve Tool for Volkswagen 65.00- (Found July 8, 2008 ) Valve Tool for Volkswagen Valve Tool for Volkswagen This unique tool has been designed to allow removal and installation of valve springs while the engine is still in the car Type I, II III engines 40 HP and later This set will also remove springs on disassembled engines.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=SC-79400C&CTMP=1&LowCt=... Valve Spring Compressor 39.99- (Found July 8, 2008 ) VALVE SPRING COMPRESSOR Used for Car & Motorcycle. Pusher size : 16mm. 19mm. 23mmm. 25mm. and 30mm. 5piece pushers for fitting the valve spring correctly and easier to compress the valve spring. Heavy Duty Motorcycle and Small Engine Valve Spring Compressor. It will compress valves for the following sizes: 1) Size: 30mm (OD.) 27.5mm (ID.) 2) Size: 25mm (OD.) 23.5mm (ID.) 3) Size: 23mm (OD.) 21.5mm (ID.) 4) Size: 19mm (OD.) 16.5mm (ID.) 5) Size: 16mm (OD.) 13.5mm...http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-EH1701&CTMP=1&LowCt=... Universal Cam Adjuster 37.95- (Found July 8, 2008 ) Universal Cam Adjuster Adjusts to Fit Different Sized Cam Sprockets. This adjustable tool is designed to both hold and turn cam sprockets. The tool is needed to turn the cam sprockets to adjust the cam position. It can also be used to hold the cam sprocket in place when removing the cam bolt. It will work on all single and dual overhead cam sprockets with holes.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=GTL-38220&CTMP=1&LowCt=... |