ZDMAK FOREIGN CAR TOOLS FOR ZDMAK SPECIALSZDMAK SPECIALS and MoreTwo Stubby Sockets 29.99- (Found July 8, 2008 ) Two Special Short Pattern SocketsOne of each 7 and 14mm.Details: The 7mm socket is 14 inch drive and the 14mm socket is 38 drive. The 14mm is designed for R&R of gearbox drain plugs. PLEASE READ: THE 14MM TOOL IS JUST UNDER 1 14 INCH LONG VERY HARD TO FIND IN THIS LENGTH AND SIZE.THE 7MM TOOL IS FOR BRAKE WORK AND IS ONLY 1 INCH LONG.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=JT-HEX714ZDM&CTMP=1&Low... Transmission Adaptor 59.95- (Found July 8, 2008 ) Transmission Adaptor Converts floor jacks into transmission jacks Fits all jacks with 1 532" removable saddle shaft Tilts forward and back and includes safety chain.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AA-41044C&CTMP=1&LowCt=... Trans Clutch Spring Compressor 59.50- (Found July 8, 2008 ) Transmission Clutch Spring Compressor. For removing and installing the trans rear clutch piston snap ring adjustable for many domestic cars and light trucks. Applies pressure to the retaining washer in the clutch drum to compress clutch piston return springs in order to remove or install snap ring during repairs or overhaul.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-1841C&CTMP=1&LowCt=0 Toyota Valve Adjustment Tool 16.99- (Found July 8, 2008 ) This tool has been designed to allow for easy valve adjustment on most Toyota overhead cam engines using spacer shims for valve adjustment. In operation, the tip of the pliers pushes between the spacer shim and the camshaft as the pliers are squeezed close. This action moves the shim and its valve lifter down from the camshaft lobe. In the down position the separate wedge tool is placed between the valve lifter ledge and the camshaft. This wedge tool then maintains a...http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-1904T&CTMP=1&LowCt=0 Toyota Master Set 99.99- (Found July 8, 2008 ) ZDMAK THREE ITEM MASTER KIT FOR TOYOTACam Tool Plus Headbolt tool Plus Valve ToolYou can read about all three of these items on this page (above). This set includes item numbers TOY4VT, plus TOYHB and 2705.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-TOY-3B&CTMP=1&LowCt=... Toyota Locknut Tool 19.99- (Found July 8, 2008 ) Toyota front wheel bearing design change requires a new procedure to remove the locknut: The free wheel hub assembly locknut is on the inside, so the hub must be removed to gain access. This wrench has a four pin design accommodates the four holes in each locknut, which prevents slippage under high torquing requirements. Works on 1995 and newer Tacoma, and 1996 and newer T100 and 4Runner.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=AW-1272C&CTMP=1&LowCt=0 Tool Bag 15.99- (Found July 8, 2008 ) Klein Tool Pouchbag. This bag is great for trasporting your favorite tools. Lightweight at .24 lbs. and made of Cordura ballistic nylon with a heavy duty zipper. Cordura is a registered trademark of INVISTA for durable fabrics. Bag displays the Klein Tools logo. Convenient storage for pliers, wrenches, screwdrivers, nut drivers, other tools and spare parts. Heavy duty nylon zipper. Constructed Of Cordura ballistic nylon. Resistant to abrasions, tears, and scuffs . Size 7" Wide X...http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-51390&CTMP=1&LowCt=0 Tie Rod Tool 45.00- (Found July 8, 2008 ) Tie Rod Tool VW 1014 Separator used for disassembly of pitman arm type tie rod ends without tearing the ball joint boots. Opening size is 25mm. Most VW Audi & Late Porsche models.Click here for a Diagram on this tool.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=1014A&CTMP=1&LowCt=0 Tie Rod Tool 39.95- (Found July 8, 2008 ) Puller P266HX Separator used for disassembly of Pitman arm type tie rod ends without tearing the boots. Opening size is 18mm. Most VW Audi Late Porsche models.Click here for a Diagram on this tool.http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=266-H&CTMP=1&LowCt=0 Tie Rod End Ball Joint Tool 29.99- (Found July 8, 2008 ) Tie Rod End Ball Joint Lifter. This labor saving tool quickly separates tie rod ends and ball joints from suspension components. Eliminates broken grease reservoirs. No need for excessive hammering. Powerful lever action breaks loose even the most stubborn joints. Works on virtually all tie rod ends and compact car ball joints. Heavy duty, all metal construction. For use with hand tools only. Heat treated drop forged steel body & bolt for long rough usage. Spread ball joints...http://www.zdmak.com/wbstore/main.asp?action=PROD&PROD=MK-1954G&CTMP=1&LowCt=0 |